Transfer Instructions
TRANSFER INSTRUCTIONS
SCREEN PRINTS (Neon, Single Colour, Full Colour):-
TEMP: 325F-350F
TIME: 15-20 SECONDS
PRESSURE: HEAVY (HEAT PRESS REQUIRED)
ANY COLOUR / FABRIC
HOT PEEL
SCREEN PRINTS (Glow in the Dark):-
Recommended for cotton shirts. If polyester is present, place parchment paper inside the shirt.
TEMP: 350F
TIME: PRE-PRESS FOR 7 SECONDS. PRESS 7-12 SECONDS
PRESSURE: HEAVY (HEAT PRESS REQUIRED)
HOT PEEL - PEEL SLOWLY, IF IT IS STICKING INCREASE YOUR HEAT AND PRESS IT AGAIN UNTIL IT PEELS EASILY. IF THE PRINT IS DULL IT WAS PRESSED TOO HOT, IF IT IS STICKING YOUR HEAT IS NOT HIGH ENOUGH.
DTF:-
TEMP: Cotton Blend 280 F - 300 F
Polyester / Polyester Blends 260 F - 280 F
TIME: 8-10 SECONDS
PRESSURE: HEAVY (HEAT PRESS REQUIRED)
REMOVE TRANSFER SLOWLY
COVER WITH CRAFT PAPER AND REPRESS, 8-10 SECONDS
CHENILLE PATCHES:-
TEMP: 325°F
PRE PRESS FOR 5-10 SECONDS TO REMOVE MOISTURE AND WRINKLES FROM GARMENT
COVER WITH TEFLON
PRESS FOR 20 SECONDS HEAVY PRESSURE
TURN GARMENT INSIDE OUT AND PRESS UNDERNEATH THE PATCH FOR ANOTHER 20 SECONDS TO ENSURE GREAT ADHESION.
GLITTER WITH RHINESTONES:-
Temp: 350°F
Pressure: Heavy
Time: 15-20 Seconds
Rub with a cloth to help adhesion and cooling
Peel: Warm
PUFF PRINT:-
Pre-Press Garment for 5 seconds to get out any moisture.
Temp: 310 - 325°F
Pressure: Heavy
Time: 7-10 Seconds
Peel: Hot
Do not cover with any Teflon etc. If print needs an additional press, please use parchment paper over it
UV DTF:-
1. Peel design transfer off of backing.
2. Place the transfer on the cup ensuring design is straight and positioned correctly.
(The adhesive is very strong. Once the transfer touches the glass its impossible to take off)
3. Press the transfer down, working from the centre outwards, pushing out any bubbles.
4. Rub all over the design with your fingers. The more rubbing the better.
5. Peel clear film off and you're done!
Hand wash only. We do not advise to put in dishwasher or microwave.
We are not responsible for application mishaps.
RHINESTONE TRANSFERS: -
TEMP: 350F
PRE-PRESS GARMENT
PRESSURE: HEAVY
REMOVE THE BACKING
TIME: 13 SECONDS
LET COOL AND REMOVE PLASTIC SLOWLY.
PRESS AGAIN FOR 5 SECONDS
USE CRAFT PAPER INBETWEEN FRONT AND BACK OF SHIRT IN CASE OF ADHESIVE LEAK
SPANGLE TRANSFERS: -
SET HEAT PRESS TO 302 DEGREES
PRE-PRESS GARMENT FOR 3-5 SECONDS
(TO REMOVE WRINKLES & MOISTURE)
APPLY TRANSFER ON GARMENT & PRESS FOR 5-7 SECONDS
USE HEAVY PRESSURE, COLD PEEL
DO NOT USE TEFLON SHEET
HTV TRANSFERS: -
* Preheat Press to 300°
* Remove paper backing gently from your HTV Transfer
* Remove any lint from your T-Shirt with a with lint roller
* Place your ECO SOLVENT TRANSFER design unto shirt, sticky area touches shirt.
* Cover design completely with Teflon sheet.
* Press for 25 seconds
* Wait 5 seconds and peel warm
* Seal press design 15-20 seconds placing Teflon sheet on top.